热熔突起型标线涂料
Hot-Applied Thermoplastic pavement marking material is 100% solid and liquefies to pavement when heated. Hot-Applied Thermoplastic pavement marking material is durable, practical and enhances retroreflectivity. Hot-Applied Thermoplastic pavement marking material is a 100% solid, environmentally and user safe compound containing pigments, glass beads, binder, and filler which becomes liquid when heated.
Hot-Applied Thermoplastic pavement marking material is 100% solid and liquefies to pavement when heated. Hot-Applied Thermoplastic pavement marking material is durable, practical and enhances retroreflectivity. Hot-Applied Thermoplastic pavement marking material is a 100% solid, environmentally and user safe compound containing pigments, glass beads, binder, and filler which becomes liquid when heated.
热熔突起型路面标线涂料是在普通反光标线涂料的基础上演变而来,添加适量的成型助剂,即可达到突起效果,热熔突起型标线涂料目前突起形状一般以块状为主,块状突起形状标线占市场份额99%以上,其他形状:圆点状,排骨状等。热熔突起型标线涂料生产相对简单,保证50℃时的抗压强度及施工性能即可。
检 测 项 目 |
技 术 要 求 | ||||
1. | 密度(g/cm3) | 1.8~2.3 | |||
2. | 软化点(℃) | ≥100 | |||
3. | 不粘胎干燥时间(min) | ≤3 | |||
4. | 涂膜外观 | 干燥后,应无皱纹、斑点、起泡、裂纹、脱落、粘胎现象,涂膜的颜色和外观应与标准板差别不大。 | |||
5. | 色 度 性 能 (45°/0°) |
白色 | 色品坐标(x,y) | 在以下四角点色品坐标组成的四边形内 (0.350,0.360);(0.300,0.310); (0.290,0.320);(0.340,0.370) |
|
亮度因数 | ≥0.75 | ||||
黄色 | 色品坐标(x,y) | 在以下四角点色品坐标组成的四边形内 (0.519,0.480);(0.468,0.442); (0.427,0.483);(0.465,0.534) |
|||
亮度因数 | ≥0.45 | ||||
6. | 抗压强度(MPa) | 23℃±1℃ | ≥12 | ||
50℃±2℃ | ≥2 | ||||
7. | 耐水性 | 在水中浸泡24h,应无异常现象。 | |||
8. | 耐碱性 | 在饱和氢氧化钙饱和溶液中浸泡24h,应无异常现象。 | |||
9. | 玻璃珠含量(%) | 18~25 | |||
10. | 涂层低温抗裂 | -10℃保持4h,室温放置4h为一个循环,连续做三个循环后应无裂纹。 | |||
11. | 加热稳定性 | 200℃~220℃在搅拌状态下保持4h,应无明显泛黄、焦化、结块等现象。 |
热熔突起型标线涂料参考配方:
在普通热熔型反光标线涂料基础上添加1公斤/吨左右的氧化聚乙烯蜡即可,也可施工队伍自己购买氧化聚乙烯蜡,施工现场添加
在普通热熔型反光标线涂料基础上添加1公斤/吨左右的氧化聚乙烯蜡即可,也可施工队伍自己购买氧化聚乙烯蜡,施工现场添加

热熔突起型标线涂料融化后在容器内状态:
搅拌时应感觉十分轻松,惰性表现力很强,同时流动性又很好,在这种状态下的热熔突起型涂料施工性最佳。并且不受温度高低的影响,高温下还能继续成型并能施工。涂料细腻,柔软,干燥后坚硬,是热熔突起标线涂料的最优配方,施工成型性能不受温度高低影响。

突起型热熔标线突起形状:



施工机械:


施工图片:

施工工艺:
同热熔反光标线
热熔突起型标线施工视频:
热熔突起型标线粘结强度试验: