抗裂型热熔反光路面标线涂料
Hot-Applied Thermoplastic pavement marking material is 100% solid and liquefies to pavement when heated. Hot-Applied Thermoplastic pavement marking material is durable, practical and enhances retroreflectivity. Hot-Applied Thermoplastic pavement marking material is a 100% solid, environmentally and user safe compound containing pigments, glass beads, binder, and filler which becomes liquid when heated.
Hot-Applied Thermoplastic pavement marking material is 100% solid and liquefies to pavement when heated. Hot-Applied Thermoplastic pavement marking material is durable, practical and enhances retroreflectivity. Hot-Applied Thermoplastic pavement marking material is a 100% solid, environmentally and user safe compound containing pigments, glass beads, binder, and filler which becomes liquid when heated.
热熔抗开裂路面标线涂料是在热熔反光型路面标线涂料的基础上,为了解决高寒季冻区公路道路交通标线材料的预期使用命,并有效解决高原高寒季冻区公路和城市道路普遍存在的道路交通标线材料开裂严重、耐久性差、视认性差难题而研发的一种功能性路面标线涂料。
抗开裂型三级干湿态持续反光标线技术要求




项 目 | 热熔反光型 | 热熔突起型 | |||
密度(g/cm) | 1.8-2.3 | ||||
软化点(℃) | 100-140 | ||||
涂膜外观 | 干燥后无皱纹、斑点、裂纹、脱落及发粘现象 | ||||
不粘胎时间(min) | ≤5 | ||||
抗压强度(Mpa) | 23℃±1℃ | ≥12 | |||
施工性能 | 温度在210℃±10℃范围内,玻璃珠沉降均匀,沉降比例在60%左右 | ||||
亮度因数 | ≥0.8 | ||||
色度性能 | 应符合JT/T280-2004中表6和图1规定的范围 | ||||
耐磨性(3000转/1000g后减重mg) | ≤300(应先预转50转后,样板表面清理干净,重新计量) | ||||
耐碱性 | 在氢氧化钙饱和溶液中浸24h无异常现象 | ||||
耐候性 | 经12个月试验,涂膜的起皱、斑点、裂纹、脱落及色变等都不大于标准样板 | ||||
内混玻璃珠含量(%) | ≥30 | ||||
内混玻璃珠成圆率(%) | ≥90 | ||||
抗开裂性(mm) | ≥4 | ||||
流动度(mm²/g) | 90±5 | 50±5 | |||
涂层低温抗裂性 | -10℃保持 4h,室温放置 4h 为一个循环,连续做三个循环后应无裂纹 | ||||
加热稳定性 |
210℃±10℃在搅拌状态下保持 4h,此过程中涂料应无明显泛黄、焦化、结块等现象;加热 4h 后,涂层色品坐标应符合JT/T 280-2004表 6 和图 1 规定的范围,涂层亮度因数不小于0.75 | ||||
逆反射亮度系数 (mcd/m²/lx) |
白色 |
干燥状态 | ≥350 | ≥350 | |
潮湿状态 | ≥175 | ≥175 | |||
黄色 |
干燥状态 | ≥350 | ≥350 | ||
潮湿状态 | ≥175 | ≥175 |
热熔抗裂型标线涂料基础配方:

树脂:石油树脂(不限制品牌型号)
DOP(工业级)
聚乙烯蜡(不限制品牌型号)
更多详细内容:
http://www.biaoxian.org.cn/index.php?m=content&c=index&a=show&catid=13&id=49

树脂:石油树脂(不限制品牌型号)
DOP(工业级)
聚乙烯蜡(不限制品牌型号)
更多详细内容:
http://www.biaoxian.org.cn/index.php?m=content&c=index&a=show&catid=13&id=49